The whole contained material in this site web is only to educational purpose. We decline our responsibility from other purposes.
Fausto Cards Support:
Require phoenix card progger (freq 3.58 mhz)
9 pin serial cable connected from card progger to pc
Will work like a card reader (2 on base unit + card progger = 3 cards can be used at same time)
Work with Fausto emulator,it mean card decoding will work after FE connected (tab "Monitor")
Will work with all cams connected on local network, like FE
Priority always gived to emulator first then to card


Phoenix mode:
Irdeto 1/2 3.58 & 6.00 MHZ (More faster at 6.00 MHZ)
Seca 1/2 3.58 & 6.00 MHZ (More faster at 6.00 MHZ)
Viaccess 1/2 3.58 MHZ
Conax 3.58 & 6.00 MHZ (More faster at 6.00 MHZ)
DreamCrypt 3.58 MHZ
VG2 3.58 MHZ
Nagravision 3.58 Mhz


How to:
1.Switch card progger into phoenix mode 3.58 mhz (tested cas3 & infinity usb phoenix)
2.Introduce official card on card progger
3.Under fausto Clic on tab "Monitor"
4.Press "Connect" button
5.Clic on Tab "Cards"
6.Select com port where connected phoenix card progger
7.Press "Connect" button
If card supported by fausto card infos will be showed
Now card will be used too for decoding Ecms
If you insert a new same kind card when FE running press button "Card Reset" on tab "Cards"
NOTA: possible to establish connection with card first, then run FE & vice versa


Datas Showed on tab Cards:
Com Port = Port used with phoenix card progger
Connect/Disconnect = connect: Card ecm decryption used with FE.
Disconnect: stop to use card ecm decryption
- Card Reset = used when you change card with same coding system
(example actual irdeto card replaced by another irdeto card)
- Clear Datas = clean datas: CW,SID,Provid,CAID,CARD,ECM
- Card infos = Informations about card inserted
- CW Decrypted= Control Word decrypted sent to cam by FE
(can be showed under tracker too if option active on monitor)
- SID,ProvId,CAID,ECM = information about current chanel
(can be showed under tracker too if option active on monitor)
- Card Type = card type inserted
(can be showed under tracker too if option active on monitor)
- Status Bar Message = Information about ecm decryption


Local Popup Menu:
- Log Traffic:
if menu option ticked Log will start (untick menu option=stop log at any moment)
all datas will be stored on file Fausto Card Log.txt
Log can be started at any moment
Example if card infos must not shared, activate log traffic just after card connection
(=Card infos stay private)
If atr found but error on card init, log file store latest instruction executed correctly
Log file datas:
Header file= Fausto Signature
Card Type = Type of card inserted
ATR = ATR of the card
"FE->Card" = Instruction sent to card
"Card->FE" = Response from card
"TO Cam" = Final CW Decrypted sent to cam (same CW showed on tab "Cards")
- Phoenix Mode 3.58 MHZ you must select same frequency on card progger option
- Phoenix Mode 6.00 MHZ you must select same frequency on card progger option
- Show Infos: show datas about card decryption (Caid/Prid/ECM/CW/...)


Direct Control Word:
Easy for all user to get DCW Key when chanel on Constant Control Word
(=only 1 ecm incoming for provid concerned when switch on chanel)
Just Copy CW on tab Cards
Enter key value on provider concerned (Services folder -> SID + Fixed COntrol Word)
Paste the key on Fixed Control Word
Now value can be used directly by Emulators (FE/Cam emulator) & shared with all users


Somes datas on cards.ini about
-Irdeto CamKey
-cryptoworks
-Conax
-VG
-Nagravision


AutoUpdate:
No EMM receive from base can't be autoupdate
Card updated with card server if emms sent by client (linux box)


Card Supported:
Seca 1/2
Viaccess 1/2
Irdeto 1/2
Conax
DreamCrypt
VideoGuard 2/3
Nagravision 2/3